被下人玩弄的嫡女NP,一尘网中国投资资讯网,五个黑人玩一个女5P视频,精品国产国偷自产在线观看

Focusing on fluid control equipment such as dispensing and dispensing

High accuracy/adaptability/flexibility

National Hotline:

0512-55198662

Your current locationHome page > Information dynamic  > Industry Dynamics return

What is the working principle of FPC glue dispensing machine

source:m.5songhua.com  |  Release time:2025年01月14日
1. Principle of glue supply system
      The FPC glue dispenser first needs a stable glue supply system. Usually, the glue solution is stored in a rubber drum or hose. The adhesive liquid is transported to the adhesive supply area near the dispensing needle under its own gravity or air pressure. For example, for some adhesives with low viscosity, slow flow can be achieved by relying on gravity; For adhesives with high viscosity, it is necessary to apply a certain pressure to the glue barrel through a pneumatic device (such as a pneumatic pump) to send the glue to the dispensing position.
2. Glue dispensing control principle
      Time pressure control method: This is a common control method. There is a pressure control system inside the glue dispensing machine, which controls the flow rate of the glue by adjusting the air pressure inside the glue supply pipeline. At the same time, combined with time control, the amount of glue is determined by controlling the length of time the glue liquid flows out. For example, when a small glue point needs to be clicked, a lower air pressure and shorter glue dispensing time will be set; For longer glue lines, the glue dispensing time will be appropriately extended. Specifically, the system will open the dispensing valve according to preset parameters, and the adhesive liquid will flow out of the needle under the pressure of air. After a correctly calculated time, the valve will close and stop dispensing.
      Piston control method: This method is similar to the principle of a syringe. There is a piston structure in the dispensing machine, and when the piston moves upward, the adhesive liquid is sucked into the piston chamber; When the piston moves downwards, the glue is squeezed out through the needle. The movement of the piston can be driven by an electric motor or air pressure. By correctly controlling the stroke and speed of the piston, the amount of glue can be controlled correctly. For example, for some high-precision FPC packages, piston control can more accurately squeeze out trace amounts of glue, avoiding excessive or insufficient glue.
      Screw control method: The glue liquid is transported and extruded in the pipeline through the rotation of the screw. When the screw rotates, it will generate a forward thrust on the glue, causing the glue to flow along the direction of the screw thread and be squeezed out from the needle. The speed of the screw can be controlled correctly, and the faster the speed, the greater the flow rate of the adhesive. This method is suitable for adhesives with high viscosity and poor fluidity, as the rotation of the screw can effectively overcome the resistance of the adhesive and achieve stable dispensing.
3. Principle of motion control
      FPC glue dispensing machines are generally equipped with high-precision motion control systems, which are usually composed of motors, screws, guide rails, and motion control cards. The motor drives the screw to rotate, and the screw drives the dispensing needle to perform correct linear motion (X, Y axis direction) on the guide rail. For example, when dispensing on FPC circuit boards, the control system will correctly move the dispensing needle to each position that needs to be dispensed according to the pre programmed path. Some dispensing machines also have Z-axis motion control to adjust the distance between the needle and the FPC board, ensuring the correct dispensing height and preventing the needle from damaging the circuit board or dispensing incorrectly due to excessive distance.
4. Visual positioning principle (if there is a visual system)
       Some good FPC dispensing machines are equipped with visual positioning systems. Its working principle is to capture images of the FPC circuit board through a camera, and then analyze the images using image recognition software. The software will recognize specific marks on the circuit board (such as positioning holes, circuit patterns, etc.) and calculate the position coordinates of these marks. Compare and calibrate these coordinates with the pre-set dispensing position coordinates to achieve high-precision dispensing position positioning. For example, in some high-precision FPC chip packaging and dispensing processes, the visual positioning system can correctly find the position of the chip pins, and the error can be controlled within a very small range to ensure that the glue is correctly applied around the pins.
亚洲人成在线观看| 久久久久久精品免费看sss| 人妻熟人中文字幕一区二区| 男女激情视频| 一本一道波多野结衣AV视频| 公开高潮当众露出羞耻h| 白嫩日本少妇做爰| 拍裸戏时被c了h| 欢乐颂3电视剧全集免费观看| 小洁和公h文翁17| 杨门十二寡妇肉床艳史电影| 裸体丰满白嫩大尺度尤物| 国产av精品一区二区三| 亚洲国产一区二区精品专区发布| 亚洲精品无码久久久久久久| 国产精品久久久久久无码av片| 无遮挡h纯肉动漫在线播放| 亚洲av无码成人精品区| 巜疯狂的少妇4做爰| 国产人妻大战黑人20p| 99国产午夜精品一区二区| 解开人妻的裙子猛烈进入| 日本xxxx69hd老师学生| 色偷拍 自怕 亚洲 30p| 精品av无码国产一区二区| 小处雏一区二区三区精品视频| 色喜国模私密浓毛私拍人体图片| 宿舍玩弄六个女同学高txt| 99e久热只有精品8在线直播| 国产精品久久久久一区二区三区 | 国产精品久久久久日本影院| 亚洲精品色情app在线下载观看| 伊人狠狠色丁香婷婷综合尤物| 精品一二三区久久aaa片| 成人性毛片免费观看黄| 欧美精品一区二区| 韩国禁止的爱HD中字在线下载| 3d动漫精品啪啪一区二区| 精品人妻人人爽久久爽av蜜桃| 口述他进我身体全过程| 女女互揉吃奶揉到高潮视频|